My Bv-300 and a small question

Discussion in 'Accurate Fishing Reels Support Forum' started by jrod*62, Mar 21, 2019.

  1. jrod*62

    jrod*62 Can't get enough

    Location:
    Crystalaire Ca
    Name:
    Jared Hollers
    Boat:
    aggressor
    • Messages:
      (78)
    • Likes Received:
      (14)
    9526C2F9-DF65-4E2E-94B3-E7A9BAAAE898.jpeg 708E6AF0-5F49-420A-B89B-84C59C1D4B7F.jpeg BDEADC60-1F92-44FD-9A87-6D1477940DB5.jpeg BF339686-4F9A-4561-B87C-5FFC37ABFFCA.jpeg 8EA43005-F9FB-41A3-A370-6A3739384130.jpeg I recently bought a used bv300 that had a pretty deep scratch and needed a service. I tore the reel down and anodized it. In reassembly I had one question... when the component is listed in the parts list such as a washer it has three sets of numbers I’m assuming it’s ID,OD and thickness? Sorry if this has been covered
     
    EL COMA and graywolf like this.
  2. hucklongfin

    hucklongfin Deep release specialist

    Location:
    Mission Viejo
    Name:
    MarkT
    Boat:
    Blazer Bay 1860
    • Messages:
      (7,603)
    • Likes Received:
      (4,477)
    Wow, looks great! I think you’re right about the washer but you could measure it yourself to confirm.
     
  3. jrod*62

    jrod*62 Can't get enough

    Location:
    Crystalaire Ca
    Name:
    Jared Hollers
    Boat:
    aggressor
    • Messages:
      (78)
    • Likes Received:
      (14)
    That’s what I ended up doing but I wanted to make sure i was going to remake the Teflon washer my tern that I bought used... it likes to eat them so I figured since I was making them for that reel I’ll make some for this one too . And thank you I’m pretty stoked on how it turned out
     
  4. abj5150

    abj5150 Service Technician, Advisor and Customer Support. Advertiser

    Location:
    USA
    Name:
    Al
    Boat:
    Whatever I can get on
    • Messages:
      (218)
    • Likes Received:
      (92)
    Your assumption is correct. ID, OD and THICKNESS. No need to make the washers yourself. They are very inexpensive.
    I forgot to comment, that is a beautiful anodizing job
     
    rexor_rn likes this.
  5. killerfin

    killerfin You fight like a girl !!!

    Location:
    santa ana
    Name:
    Felipe
    Boat:
    Your Mama
    • Messages:
      (494)
    • Likes Received:
      (39)


    did you make rod clamp?
     
  6. jrod*62

    jrod*62 Can't get enough

    Location:
    Crystalaire Ca
    Name:
    Jared Hollers
    Boat:
    aggressor
    • Messages:
      (78)
    • Likes Received:
      (14)
    I made the washers just because I had the Material and the tools the quick search I did I came up empty but I was searching the wrong description. and thank you ! After doing this I’m considering doing the same to my bv2-600 ... maybe after the warranty tho
     
  7. jrod*62

    jrod*62 Can't get enough

    Location:
    Crystalaire Ca
    Name:
    Jared Hollers
    Boat:
    aggressor
    • Messages:
      (78)
    • Likes Received:
      (14)
    Nope it’s made by Tiburon I just anodized it to Match the reel
     
    Wildman likes this.
  8. killerfin

    killerfin You fight like a girl !!!

    Location:
    santa ana
    Name:
    Felipe
    Boat:
    Your Mama
    • Messages:
      (494)
    • Likes Received:
      (39)
    do you happen to have the name for the Tiburon one or part number?
     
  9. jrod*62

    jrod*62 Can't get enough

    Location:
    Crystalaire Ca
    Name:
    Jared Hollers
    Boat:
    aggressor
    • Messages:
      (78)
    • Likes Received:
      (14)
    The part number is TCU-VAL 300
     
    Wildman likes this.
  10. Bob2002

    Bob2002 Newbie

    Location:
    NJ
    Name:
    Bob
    Boat:
    2002 Trophy
    • Messages:
      (6)
    • Likes Received:
      (0)
    That looks awesome, good job
     
  11. killerfin

    killerfin You fight like a girl !!!

    Location:
    santa ana
    Name:
    Felipe
    Boat:
    Your Mama
    • Messages:
      (494)
    • Likes Received:
      (39)


    thank you
     
  12. abj5150

    abj5150 Service Technician, Advisor and Customer Support. Advertiser

    Location:
    USA
    Name:
    Al
    Boat:
    Whatever I can get on
    • Messages:
      (218)
    • Likes Received:
      (92)
    You can contact Accurate to order the Tiburon Clamp. The part number we use is TC-1. www.accuratefishing.com
     
  13. Shanethelipripper

    Shanethelipripper Member

    Location:
    Huntington Beach
    Name:
    Shane
    Boat:
    Alex
    • Messages:
      (315)
    • Likes Received:
      (64)
    How much did that cost to anodize it
     
  14. cali_reef

    cali_reef Newbie

    Location:
    Palos Verdes
    Name:
    Pierce
    Boat:
    Marlin 300
    • Messages:
      (27)
    • Likes Received:
      (13)
    That custom reel look awesome.
     

Share This Page