85 Outrage Rehab

tranandya

Fishy
Aug 18, 2010
447
100
Anaheim
Name
Andy
Boat
Maritime 20p
Looking good! Dog house is definitely the way to go. One recommendation is add a return on the roof to stiffen it up and prevent water from dripping down your back on wet days..kinda hard to see but hope this clears things up

20210615_204115.jpg
 
Upvote 0

tranandya

Fishy
Aug 18, 2010
447
100
Anaheim
Name
Andy
Boat
Maritime 20p
 
Upvote 0

gettingbentwithbo

Subscribe to my YouTube Channel!
Mar 7, 2009
2,733
1,478
Riverside
gettingbentwithbo.com
Name
Bo
Boat
16' Starcraft SF SS
Jesus christ you got skills brother! Loving this build so much!
 
  • Like
Reactions: acefuture
Upvote 0

karlow

Twins 2017
Apr 29, 2004
1,899
817
64
Duarte/Covina
Name
karl
Boat
20' skippy Topless /17' whaler Wet Ride (sold) /18' Outrage
I was out fishing on the shoe on Sat, There was a whaler out there with the tiny house on it. It may have been an 18 footer, it looked nice, but i'm not sure it provides a lot of protection if there is more than one person on the boat. Iliked the look.
 
Upvote 0

flytie

Member
Oct 20, 2012
847
1,112
Orange, CA USA
Name
GC
Boat
Out of Office - Custom Invader CC
Dude, do you have two boat projects going?

Oh my, I will pray for you! One is enough.
 
Upvote 0

acefuture

@acecraftco
Apr 3, 2019
672
666
Costa Mesa, CA
Name
Ace
Boat
Always changing
Dude, do you have two boat projects going?

Oh my, I will pray for you! One is enough.
At one point I had 4....Now I'm full focus on the whaler and the bayrunner can sit and rot until I get some blood on the decks of the whaler. But I just picked up a project golf cart I need to get running too. I may have a problem (at least that's what my lady says)
 
Upvote 0

flytie

Member
Oct 20, 2012
847
1,112
Orange, CA USA
Name
GC
Boat
Out of Office - Custom Invader CC
At one point I had 4....Now I'm full focus on the whaler and the bayrunner can sit and rot until I get some blood on the decks of the whaler. But I just picked up a project golf cart I need to get running too. I may have a problem (at least that's what my lady says)
Don't feel bad. I went from rebuilding the boat to rebuilding my RV. Not a "lipstick" job, more full on rehab.

My neighbors think I'm nuts. I agree.
 
Upvote 0

acefuture

@acecraftco
Apr 3, 2019
672
666
Costa Mesa, CA
Name
Ace
Boat
Always changing
Don't feel bad. I went from rebuilding the boat to rebuilding my RV. Not a "lipstick" job, more full on rehab.

My neighbors think I'm nuts. I agree.
Oh my neighbors know I’m nuts. My toy hauler is in one neighbors driveway, and my sand car is as well. Then at one point the whaler was in another neighbors driveway while I had 3 boats in my driveway. Luckily they are all cool and let me leave my stuff thrown about the neighborhood. I need to consolidate at some point. But that’s unlikely
 
Upvote 0

acefuture

@acecraftco
Apr 3, 2019
672
666
Costa Mesa, CA
Name
Ace
Boat
Always changing
Here’s a quick update shot. Interior is glassed with 2 layers on all joints, and 3 layers in corners of 1708. Inside the console just a single layer of 1708. Exterior is started, whole thing will get 2 layers of 1708. Then I’ll finish the console with a layer of 10oz and then CSM

D23F2B39-8470-4EA6-88C9-39A1F318C7C0.jpeg
BBDA0192-F2DA-4D27-B4D3-FC00B0177918.jpeg
 
Last edited:
Upvote 0

karlow

Twins 2017
Apr 29, 2004
1,899
817
64
Duarte/Covina
Name
karl
Boat
20' skippy Topless /17' whaler Wet Ride (sold) /18' Outrage
You need a better solution for the edges of the wood. That is where the failure will start. I'm not sure what the solution is. Maybe your suppose to start by just wrapping all of the edges with glass first. Typically they end up with little or no glass on them after sanding and grinding with the wood exposed. Maybe they make a 1/4" or 3/8" wide glass tape. then you could bond the edges of all of the wood first. Then grind them, wrap them in glass and build from there.
 
Upvote 0

acefuture

@acecraftco
Apr 3, 2019
672
666
Costa Mesa, CA
Name
Ace
Boat
Always changing
You need a better solution for the edges of the wood. That is where the failure will start. I'm not sure what the solution is. Maybe your suppose to start by just wrapping all of the edges with glass first. Typically they end up with little or no glass on them after sanding and grinding with the wood exposed. Maybe they make a 1/4" or 3/8" wide glass tape. then you could bond the edges of all of the wood first. Then grind them, wrap them in glass and build from there.
Many of them already have 10oz tape on them. Once completely glassed all edges will get another layer of 10oz tape, as well as CSM. No wood will be exposed
 
Upvote 0